This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.
Note: you will need a FarmRoad account before you can set up your Folium. You should have received an email from us and confirmation with your log in details. You will need to confirm your account via email. If you have not received anything please contact your Account Manager or WayBeyond support.
Connect the gateway to the FarmRoad platform
Folium sends data to the FarmRoad platform through a supplied gateway, which is housed in a weatherproof plastic box.The gateway can connect to the internet in one of two ways:
Ethernet/LAN cable connection to your router or internet access point (recommended)
Wi-Fi connection
Wi-Fi connections can be affected by structural barriers such as walls or buildings and are generally less stable than Ethernet. If you use Wi-Fi, you may experience an intermittent connection.
Connect the gateway using Ethernet
Remove the screws from the box lid to access the gateway.
Feed the power cord through the cable gland hole and plug it into the gateway to power it on.
Feed the supplied Ethernet/LAN cable through the cable gland hole and into the gateway. Plug the other end into your router or internet access point.
Screw the antenna onto the brass thread on the outside of the weatherproof box, then replace the lid.
The gateway will automatically connect to the FarmRoad platform. You can confirm activity by checking that the lights next to the Ethernet connector are blinking.
Connect the gateway using Wi-Fi
To set up Wi-Fi, the gateway must first be connected to your network using Ethernet. Complete the Ethernet setup steps above before continuing.
Make a note of the gateway’s 7-digit serial number shown on the sticker on the box lid.
On your PC or mobile device, open a new browser window.
Enter the following address in the address bar: http://[gatewayserialno].local:3333 Example: http://qcil1234567.local:3333
The gateway configuration page will open.
Enter your Wi-Fi SSID and password, then click Connect.
The text WiFi Status: Disconnected should change to WiFi Status: Connected.
You can now disconnect the Ethernet cable and move the gateway to any location with Wi-Fi coverage.
Install the Folium / FarmRoad sensor in your growing environment
Folium sensors are powered by 2 C-cell batteries.Before powering, installing, and setting up your Folium sensor, make sure you have:
A FarmRoad account
Connected a Folium gateway device to the internet
Onboarded your Folium device to the FarmRoad platform
Install your sensors
Screw the antenna into each Folium sensor.
Insert the batteries into the battery enclosure and close the lid.
Note the serial number of each Folium sensor and the planned location for each one. You will need this information when setting up the devices in your FarmRoad account. See here for more information.
We recommend testing your units in the office first to confirm everything is working as expected before moving them into your growing environment.
Sensor placement recommendations
For the best measurements in your growing area:
Hang Folium devices above the crop canopy and within line of sight of the gateway.
Evenly distribute your Folium sensors through your growing area. Make sure each sensor is within range of the gateway. You’ll be able to confirm this when you log in to FarmRoad, and you may need to adjust placement at that stage.
Do not place sensors at the perimeter or near walls.
Do not place sensors in aisles, as airflow there may not represent typical growing conditions.
Suspend sensors slightly above the crop canopy and immediately adjacent to the plants.
Do not cover the top of the sensor, as this will cause inaccurate light measurements.
Level the sensor as much as possible. The wires attached to the top should help the sensor hang close to level.
Press the power button on the bottom of the Folium.
The sensor will flash green for 3 seconds to show it is powered on and starting its self-test.
The light will then show solid green for approximately 30 seconds, indicating the sensor is operating normally.
{"docsConfig":{"theme":"mint","$schema":"https://mintlify.com/docs.json","name":"WayBeyond","colors":{"primary":"#3e2ac0","light":"#7D70E0","dark":"#3f30c0"},"logo":{"light":"https://mintcdn.com/waybeyond/Q_XCFfJaiUU-wMpp/images/WBlogolight.png?fit=max\u0026auto=format\u0026n=Q_XCFfJaiUU-wMpp\u0026q=85\u0026s=678159c74be8000d94119267ab533abe","dark":"https://mintcdn.com/waybeyond/Q_XCFfJaiUU-wMpp/images/WBlogodark.png?fit=max\u0026auto=format\u0026n=Q_XCFfJaiUU-wMpp\u0026q=85\u0026s=4b552189054c70a91251612cc8c5ea69","href":"https://waybeyond.mintlify.app/en/overview"},"favicon":{"light":"https://mintcdn.com/waybeyond/Tt6Pmap3OqSpIiq6/images/Favicon--white-green-48x48.png?fit=max\u0026auto=format\u0026n=Tt6Pmap3OqSpIiq6\u0026q=85\u0026s=2cdd93bd137dd39774898134b2c3e515","dark":"https://mintcdn.com/waybeyond/Tt6Pmap3OqSpIiq6/images/Favicon--white-green-48x48.png?fit=max\u0026auto=format\u0026n=Tt6Pmap3OqSpIiq6\u0026q=85\u0026s=2cdd93bd137dd39774898134b2c3e515"},"navbar":{"primary":{"type":"button","label":"Contact Support","href":"mailto:support@waybeyond.io"}},"footer":{"socials":{"x":"https://x.com/waybeyond_io","youtube":"https://www.youtube.com/channel/UCzoomuJSl6B1szeECg9HMwQ","linkedin":"https://www.linkedin.com/company","website":"https://www.waybeyond.io/","facebook":"https://www.facebook.com/waybeyond.io","instagram":"https://www.instagram.com/waybeyond.io"}},"seo":{"indexing":"all"},"styling":{"eyebrows":"breadcrumbs","latex":true},"integrations":{"ga4":{"measurementId":"G-05PQKQN0CG"}},"interaction":{"drilldown":false},"navigation":{"languages":[{"language":"en","default":true,"href":"en/overview"},{"language":"fr","href":"fr/overview"},{"language":"es","href":"es/overview"}]}},"deployment":{"deploymentMetadataValue":{"subdomain":"waybeyond","hasAudioNarration":false,"actualSubdomain":"waybeyond","customDomains":[],"gitSource":{"type":"github","owner":"mintlify-community","repo":"docs-waybeyond-e022d9ec","deployBranch":"main","contentDirectory":"","isPrivate":true,"mountPath":"","label":""},"entitlements":{"AI_CHAT":{"status":"DISABLED"}},"buildId":"6ae95aea46eff8e14e01a763:success","clientVersion":"0.0.4270","searchFilterCounts":[{"language":"en","tag":"FarmRoad","count":59},{"language":"es","tag":"FarmRoad","count":57},{"language":"fr","tag":"FarmRoad","count":57},{"language":"fr","tag":"Enregistrement des cultures","count":12},{"language":"en","tag":"Sensor \u0026 Gateway","count":9},{"language":"es","tag":"Sensor y gateway","count":9},{"language":"en","tag":"Data Studio","count":8},{"language":"es","tag":"Estudio de datos","count":8},{"language":"fr","tag":"Studio de données","count":8},{"language":"fr","tag":"Capteurs et passerelle","count":8},{"language":"en","tag":"Crop Registration","count":7},{"language":"en","tag":"Crop Insights \u0026 Grower Guides","count":7},{"language":"es","tag":"Registro de cultivos","count":7},{"language":"en","tag":"FarmRoad Mobile App","count":6},{"language":"en","tag":"Organisation Management","count":6},{"language":"es","tag":"FarmRoad Móvil","count":6},{"language":"es","tag":"Gestión de la organización","count":6},{"language":"es","tag":"Información del cultivo y guías para productores","count":6},{"language":"fr","tag":"Application mobile FarmRoad","count":6},{"language":"fr","tag":"Gestion de l’organisation","count":6},{"language":"fr","tag":"Informations sur les cultures et guides pour les producteurs","count":6},{"language":"en","tag":"Alerts / Alerting","count":5},{"language":"en","tag":"Crop Registration mobile","count":5},{"language":"en","tag":"Crop Registration Web","count":5},{"language":"es","tag":"Registro de cultivos móvil","count":5},{"language":"es","tag":"Registro de cultivos web","count":5},{"language":"fr","tag":"Alertes","count":5},{"language":"fr","tag":"Enregistrement des cultures sur le web","count":5},{"language":"es","tag":"Alertas / Alertando","count":4},{"language":"fr","tag":"Gestion des fermes","count":4}]},"assistantConfig":{"enableAskAiButton":false,"enableStarterQuestions":false,"enableContextualStarterQuestions":false,"enableAskAiSearchBar":true,"deflection":{"enabled":true,"email":"support@waybeyond.io"}},"basePath":"","hasChatPermissions":false,"hasWebMcpPermissions":false,"toggles":[{"name":"kill-isr","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-rbac-roles","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-mintlify-slack","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"agent-integrations-settings","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"rbac-expansion","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-pr-grouping","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"custom-prefix","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"analytics-v7","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"user-flows-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"no-publish-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-onboarding","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving-live","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"stripTemperatureMiddleware","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"support-platform-pylon-zendesk","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"snapshot-serving","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"instant-rollback","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications-server","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"granular-notifications","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automations-fable","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fixed-ai-action-pricing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"site-roles","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"automation-resolve-merge-conflict","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"scoped-publishing","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"mintql","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"page-level-analytics","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-version-history-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"billing-page-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"full-page-search","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workspace-projects","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"assistant-v5","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"fork-pr-previews","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"revalidation-jwt","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-sso-scim","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"hobby-abuse-scan","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"dashboard-inbox","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-signup","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-dual-write","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"workos-enabled","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"approve-review-flow","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"editor-metadata","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"sso-setup-deadline-banner","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"turbopuffer-serve","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"live-agents","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"starter-pricing","enabled":true,"variant":{"name":"control","enabled":true,"payload":{"type":"string","value":"control"},"feature_enabled":true},"impressionData":false},{"name":"llms-txt-v2","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false},{"name":"wildcard-email-auth","enabled":true,"variant":{"name":"disabled","enabled":false,"feature_enabled":true},"impressionData":false}],"googleFontsInlined":false},"customCss":[]}
{"page":{"pagePath":"en/farmroad/set-up-hardware","slug":"/en/farmroad/set-up-hardware","pageMetadata":{"title":"How do I set up my hardware?","sidebarTitle":"Set up hardware","description":"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.","href":"/en/farmroad/set-up-hardware"},"description":{"compiledSource":"\"use strict\";\nconst {jsx: _jsx} = arguments[0];\nconst {useMDXComponents: _provideComponents} = arguments[0];\nfunction _createMdxContent(props) {\n const _components = {\n p: \"p\",\n ..._provideComponents(),\n ...props.components\n };\n return _jsx(_components.p, {\n children: \"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\"\n });\n}\nfunction MDXContent(props = {}) {\n const {wrapper: MDXLayout} = {\n ..._provideComponents(),\n ...props.components\n };\n return MDXLayout ? _jsx(MDXLayout, {\n ...props,\n children: _jsx(_createMdxContent, {\n ...props\n })\n }) : _createMdxContent(props);\n}\nreturn {\n default: MDXContent\n};\n","frontmatter":{},"scope":{}},"pageType":"default","mdx":{"mdxSource":{"compiledSource":"\"use strict\";const{Fragment:_Fragment,jsx:_jsx,jsxs:_jsxs}=arguments[0];const{useMDXComponents:_provideComponents}=arguments[0];function _createMdxContent(props){const _components={a:`a`,code:`code`,li:`li`,ol:`ol`,p:`p`,strong:`strong`,ul:`ul`,..._provideComponents(),...props.components},{Heading,Tip}=_components;if(!Heading)_missingMdxReference(`Heading`,true);if(!Tip)_missingMdxReference(`Tip`,true);return _jsxs(_Fragment,{children:[_jsx(`video`,{controls:true,className:`mint-w-full mint-aspect-video mint-rounded-xl`,src:`https://5939375.fs1.hubspotusercontent-na1.net/hubfs/5939375/Folium%20Setup%20-%20Complete%20guide.mp4`}),`\n`,_jsx(_components.p,{children:`Note: you will need a FarmRoad account before you can set up your Folium. You should have received an email from us and confirmation with your log in details. You will need to confirm your account via email. If you have not received anything please contact your Account Manager or WayBeyond support.\\xA0`}),`\n`,_jsx(Heading,{level:`2`,id:`connect-the-gateway-to-the-farmroad-platform`,children:`Connect the gateway to the FarmRoad platform`}),`\n`,_jsx(_components.p,{children:`Folium sends data to the FarmRoad platform through a supplied gateway, which is housed in a weatherproof plastic box.`}),`\n`,_jsx(_components.p,{children:`The gateway can connect to the internet in one of two ways:`}),`\n`,_jsxs(_components.ul,{children:[`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Ethernet/LAN cable`}),` connection to your router or internet access point (recommended)`]}),`\n`,_jsxs(_components.li,{children:[_jsx(_components.strong,{children:`Wi-Fi`}),` connection`]}),`\n`]}),`\n`,_jsx(_components.p,{children:`Wi-Fi connections can be affected by structural barriers such as walls or buildings and are generally less stable than Ethernet. If you use Wi-Fi, you may experience an intermittent connection.`}),`\n`,_jsx(Heading,{level:`3`,id:`connect-the-gateway-using-ethernet`,children:`Connect the gateway using Ethernet`}),`\n`,_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`Remove the screws from the box lid to access the gateway.`}),`\n`,_jsx(_components.li,{children:`Feed the power cord through the cable gland hole and plug it into the gateway to power it on.`}),`\n`,_jsx(_components.li,{children:`Feed the supplied Ethernet/LAN cable through the cable gland hole and into the gateway. Plug the other end into your router or internet access point.`}),`\n`,_jsx(_components.li,{children:`Screw the antenna onto the brass thread on the outside of the weatherproof box, then replace the lid.`}),`\n`,_jsx(_components.li,{children:`The gateway will automatically connect to the FarmRoad platform. You can confirm activity by checking that the lights next to the Ethernet connector are blinking.`}),`\n`]}),`\n`,_jsx(Heading,{level:`3`,id:`connect-the-gateway-using-wi-fi`,children:`Connect the gateway using Wi-Fi`}),`\n`,_jsx(_components.p,{children:`To set up Wi-Fi, the gateway must first be connected to your network using Ethernet. Complete the Ethernet setup steps above before continuing.`}),`\n`,_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`Make a note of the gateway’s 7-digit serial number shown on the sticker on the box lid.`}),`\n`,_jsx(_components.li,{children:`On your PC or mobile device, open a new browser window.`}),`\n`,_jsxs(_components.li,{children:[`Enter the following address in the address bar: `,_jsx(_components.code,{children:`http://[gatewayserialno].local:3333`}),_jsx(`br`,{}),`Example: `,_jsx(_components.code,{children:`http://qcil1234567.local:3333`})]}),`\n`,_jsx(_components.li,{children:`The gateway configuration page will open.`}),`\n`,_jsxs(_components.li,{children:[`Enter your Wi-Fi SSID and password, then click `,_jsx(_components.strong,{children:`Connect`}),`.`]}),`\n`,_jsxs(_components.li,{children:[`The text `,_jsx(_components.strong,{children:`WiFi Status: Disconnected`}),` should change to `,_jsx(_components.strong,{children:`WiFi Status: Connected`}),`.`]}),`\n`,_jsx(_components.li,{children:`You can now disconnect the Ethernet cable and move the gateway to any location with Wi-Fi coverage.`}),`\n`]}),`\n`,_jsxs(_components.p,{children:[`For the next step, see `,_jsx(_components.a,{href:`https://waybeyond.mintlify.app/en/farmroad/onboard-a-sensor`,children:`How can I onboard a Folium device?`})]}),`\n`,_jsx(Heading,{level:`2`,id:`install-the-folium-/-farmroad-sensor-in-your-growing-environment`,children:`Install the Folium / FarmRoad sensor in your growing environment`}),`\n`,_jsxs(_components.p,{children:[`Folium sensors are powered by `,_jsx(_components.strong,{children:`2 C-cell batteries`}),`.`]}),`\n`,_jsx(_components.p,{children:`Before powering, installing, and setting up your Folium sensor, make sure you have:`}),`\n`,_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`A FarmRoad account`}),`\n`,_jsx(_components.li,{children:`Connected a Folium gateway device to the internet`}),`\n`,_jsx(_components.li,{children:`Onboarded your Folium device to the FarmRoad platform`}),`\n`]}),`\n`,_jsx(Heading,{level:`3`,id:`install-your-sensors`,children:`Install your sensors`}),`\n`,_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`Screw the antenna into each Folium sensor.`}),`\n`,_jsx(_components.li,{children:`Insert the batteries into the battery enclosure and close the lid.`}),`\n`,_jsx(_components.li,{children:`Note the serial number of each Folium sensor and the planned location for each one. You will need this information when setting up the devices in your FarmRoad account. See here for more information.`}),`\n`]}),`\n`,_jsx(Tip,{children:_jsx(_components.p,{children:`We recommend testing your units in the office first to confirm everything is working as expected before moving them into your growing environment.`})}),`\n`,_jsx(Heading,{level:`2`,id:`sensor-placement-recommendations`,children:`Sensor placement recommendations`}),`\n`,_jsx(_components.p,{children:`For the best measurements in your growing area:`}),`\n`,_jsxs(_components.ol,{children:[`\n`,_jsx(_components.li,{children:`Hang Folium devices above the crop canopy and within line of sight of the gateway.`}),`\n`,_jsx(_components.li,{children:`Evenly distribute your Folium sensors through your growing area. Make sure each sensor is within range of the gateway. You’ll be able to confirm this when you log in to FarmRoad, and you may need to adjust placement at that stage.`}),`\n`,_jsx(_components.li,{children:`Do not place sensors at the perimeter or near walls.`}),`\n`,_jsx(_components.li,{children:`Do not place sensors in aisles, as airflow there may not represent typical growing conditions.`}),`\n`,_jsx(_components.li,{children:`Suspend sensors slightly above the crop canopy and immediately adjacent to the plants.`}),`\n`,_jsx(_components.li,{children:`Do not cover the top of the sensor, as this will cause inaccurate light measurements.`}),`\n`,_jsx(_components.li,{children:`Level the sensor as much as possible. The wires attached to the top should help the sensor hang close to level.`}),`\n`,_jsx(_components.li,{children:`Press the power button on the bottom of the Folium.`}),`\n`,_jsx(_components.li,{children:`The sensor will flash green for 3 seconds to show it is powered on and starting its self-test.`}),`\n`,_jsx(_components.li,{children:`The light will then show solid green for approximately 30 seconds, indicating the sensor is operating normally.`}),`\n`]})]})}function MDXContent(props={}){const{wrapper:MDXLayout}={..._provideComponents(),...props.components};return MDXLayout?_jsx(MDXLayout,{...props,children:_jsx(_createMdxContent,{...props})}):_createMdxContent(props)}return{default:MDXContent};function _missingMdxReference(id,component){throw new Error(`Expected `+(component?`component`:`object`)+\" `\"+id+\"` to be defined: you likely forgot to import, pass, or provide it.\")}","frontmatter":{},"scope":{"config":{},"pageMetadata":{"title":"How do I set up my hardware?","sidebarTitle":"Set up hardware","description":"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.","href":"/en/farmroad/set-up-hardware"}}},"mdxSourceWithNoJs":null},"mdxExtracts":{"tableOfContents":[{"title":"Connect the gateway to the FarmRoad platform","slug":"connect-the-gateway-to-the-farmroad-platform","depth":2,"children":[{"title":"Connect the gateway using Ethernet","slug":"connect-the-gateway-using-ethernet","depth":3,"children":[]},{"title":"Connect the gateway using Wi-Fi","slug":"connect-the-gateway-using-wi-fi","depth":3,"children":[]}]},{"title":"Install the Folium / FarmRoad sensor in your growing environment","slug":"install-the-folium-/-farmroad-sensor-in-your-growing-environment","depth":2,"children":[{"title":"Install your sensors","slug":"install-your-sensors","depth":3,"children":[]}]},{"title":"Sensor placement recommendations","slug":"sensor-placement-recommendations","depth":2,"children":[]}],"codeExamples":{}},"jsLinks":[],"dynamicCss":".mint-aspect-video {\n aspect-ratio: 16 / 9\n}\n.mint-w-full {\n width: 100%\n}\n.mint-rounded-xl {\n border-radius: 0.75rem\n}","subdomain":"waybeyond","siteName":"WayBeyond","title":"How do I set up my hardware? - WayBeyond","navMaps":{"firstHrefInVersion":{},"firstHrefInLanguage":{"en":{"href":"/en/farmroad/set-up-hardware","matchLevel":0},"fr":{"href":"/fr/farmroad/set-up-hardware","matchLevel":1},"es":{"href":"/es/farmroad/set-up-hardware","matchLevel":1}}},"lastModified":"2026-07-27T05:37:56.353Z","originalFileLocation":"en/farmroad/set-up-hardware.mdx","locale":"en"},"headHtml":"\u003cscript data-mint-head>(function(){var d=document.documentElement,p=null;if(!p){try{p=localStorage.getItem(\"isDarkMode\")}catch(e){}if(p==='true')p='dark';else if(p==='false')p='light';if(p!=='light'\u0026\u0026p!=='dark'\u0026\u0026p!=='system')p=\"system\"}var r=p==='system'?(matchMedia(\"(prefers-color-scheme: dark)\").matches?'dark':'light'):p;d.classList.remove(r==='dark'?'light':'dark');d.classList.add(r);d.setAttribute(\"data-theme-preference\",p)})();\u003c/script>\u003cmeta data-mint-head name=\"description\" content=\"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\">\u003cmeta data-mint-head name=\"application-name\" content=\"WayBeyond\">\u003cmeta data-mint-head name=\"generator\" content=\"Mintlify\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/android-chrome-192x192.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"apple-touch-icon\" type=\"image/png\" sizes=\"180x180\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/apple-touch-icon.png\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/favicon-16x16.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/favicon-32x32.png\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/favicon.ico\" media=\"(prefers-color-scheme: light)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"192x192\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon-dark/android-chrome-192x192.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"16x16\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon-dark/favicon-16x16.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"icon\" type=\"image/png\" sizes=\"32x32\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon-dark/favicon-32x32.png\" media=\"(prefers-color-scheme: dark)\">\u003clink data-mint-head rel=\"shortcut icon\" type=\"image/x-icon\" href=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon-dark/favicon.ico\" media=\"(prefers-color-scheme: dark)\">\u003cmeta data-mint-head property=\"og:title\" content=\"How do I set up my hardware? - WayBeyond\">\u003cmeta data-mint-head property=\"og:description\" content=\"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\">\u003cmeta data-mint-head property=\"og:site_name\" content=\"WayBeyond\">\u003cmeta data-mint-head property=\"og:url\" content=\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\">\u003cmeta data-mint-head property=\"og:type\" content=\"website\">\u003cmeta data-mint-head property=\"og:image\" content=\"https://waybeyond.mintlify.site/_mintlify/api/og/v2?division=Sensor+%26+Gateway\u0026amp;title=How+do+I+set+up+my+hardware%3F\u0026amp;description=This+article+explains+how+to+set+up+your+Folium+gateway+and+sensors+for+data+collection+in+your+growing+environment.\u0026amp;theme=460c66de92befec6e57b9412\u0026amp;signature=64cc26dce3371452426c7874d52d0db6473e4198f43bb119bcded9f8c76b8515\">\u003cmeta data-mint-head property=\"og:image:width\" content=\"1200\">\u003cmeta data-mint-head property=\"og:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"twitter:card\" content=\"summary_large_image\">\u003cmeta data-mint-head name=\"twitter:title\" content=\"How do I set up my hardware? - WayBeyond\">\u003cmeta data-mint-head name=\"twitter:description\" content=\"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\">\u003cmeta data-mint-head name=\"twitter:image\" content=\"https://waybeyond.mintlify.site/_mintlify/api/og/v2?division=Sensor+%26+Gateway\u0026amp;title=How+do+I+set+up+my+hardware%3F\u0026amp;description=This+article+explains+how+to+set+up+your+Folium+gateway+and+sensors+for+data+collection+in+your+growing+environment.\u0026amp;theme=460c66de92befec6e57b9412\u0026amp;signature=64cc26dce3371452426c7874d52d0db6473e4198f43bb119bcded9f8c76b8515\">\u003cmeta data-mint-head name=\"twitter:image:width\" content=\"1200\">\u003cmeta data-mint-head name=\"twitter:image:height\" content=\"630\">\u003cmeta data-mint-head name=\"msapplication-config\" content=\"/mintlify-assets/_mintlify/favicons/waybeyond/3o0Yi53pXf2IGsXP/_generated/favicon/browserconfig.xml\">\u003cmeta data-mint-head name=\"apple-mobile-web-app-title\" content=\"WayBeyond\">\u003cmeta data-mint-head name=\"msapplication-TileColor\" content=\"#3e2ac0\">\u003clink data-mint-head rel=\"canonical\" href=\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\">\u003clink data-mint-head rel=\"alternate\" type=\"application/xml\" href=\"/sitemap.xml\">\u003clink data-mint-head rel=\"alternate\" type=\"text/markdown\" href=\"/en/farmroad/set-up-hardware.md\">\u003clink data-mint-head rel=\"alternate\" hreflang=\"en\" href=\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\">\u003clink data-mint-head rel=\"alternate\" hreflang=\"fr\" href=\"https://waybeyond.mintlify.app/fr/farmroad/set-up-hardware\">\u003clink data-mint-head rel=\"alternate\" hreflang=\"es\" href=\"https://waybeyond.mintlify.app/es/farmroad/set-up-hardware\">\u003clink data-mint-head rel=\"alternate\" hreflang=\"x-default\" href=\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\">\u003cscript data-mint-head type=\"application/ld+json\">{\"@context\":\"https://schema.org\",\"@graph\":[{\"@type\":\"Organization\",\"@id\":\"https://waybeyond.mintlify.app/#organization\",\"name\":\"WayBeyond\",\"url\":\"https://waybeyond.mintlify.app\",\"logo\":{\"@type\":\"ImageObject\",\"url\":\"https://mintcdn.com/waybeyond/Q_XCFfJaiUU-wMpp/images/WBlogolight.png?fit=max\u0026auto=format\u0026n=Q_XCFfJaiUU-wMpp\u0026q=85\u0026s=678159c74be8000d94119267ab533abe\"}},{\"@type\":\"WebSite\",\"@id\":\"https://waybeyond.mintlify.app#website\",\"name\":\"WayBeyond\",\"url\":\"https://waybeyond.mintlify.app\",\"publisher\":{\"@id\":\"https://waybeyond.mintlify.app/#organization\"}},{\"@type\":\"WebPage\",\"@id\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware#webpage\",\"url\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\",\"name\":\"How do I set up my hardware?\",\"description\":\"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\",\"dateModified\":\"2026-07-27T05:37:56.353Z\",\"isPartOf\":{\"@id\":\"https://waybeyond.mintlify.app#website\"},\"breadcrumb\":{\"@id\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware#breadcrumb\"}},{\"@type\":\"BreadcrumbList\",\"@id\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"FarmRoad\",\"item\":\"https://waybeyond.mintlify.app/en/farmroad/farmroad-agronomy-intelligence\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How do I set up my hardware?\",\"item\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\"}]},{\"@type\":[\"Article\",\"TechArticle\"],\"@id\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware#article\",\"headline\":\"How do I set up my hardware?\",\"name\":\"How do I set up my hardware?\",\"description\":\"This article explains how to set up your Folium gateway and sensors for data collection in your growing environment.\",\"url\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware\",\"mainEntityOfPage\":{\"@id\":\"https://waybeyond.mintlify.app/en/farmroad/set-up-hardware#webpage\"},\"dateModified\":\"2026-07-27T05:37:56.353Z\",\"publisher\":{\"@id\":\"https://waybeyond.mintlify.app/#organization\"},\"isPartOf\":{\"@id\":\"https://waybeyond.mintlify.app#website\"}}]}\u003c/script>\u003cscript data-mint-head type=\"application/ld+json\">{\"@context\":\"https://schema.org\",\"@type\":\"WebSite\",\"name\":\"WayBeyond\",\"publisher\":{\"@type\":\"Organization\",\"name\":\"WayBeyond\"},\"provider\":{\"@type\":\"Organization\",\"name\":\"Mintlify\",\"url\":\"https://mintlify.com\"}}\u003c/script>","agentPointerHref":"/en/farmroad/set-up-hardware.md","siteName":"WayBeyond","nav":{"global":null,"languages":[{"language":"en","default":true,"pages":[{"title":"Welcome to the WayBeyond Knowledge Base","sidebarTitle":"Overview","mode":"wide","href":"/en/overview"},{"group":"FarmRoad","pages":[{"group":"Agronomy Intelligence","pages":[{"title":"What is FarmRoad Agronomy Intelligence?","sidebarTitle":"Understanding FarmRoad Agronomy Intelligence","href":"/en/farmroad/farmroad-agronomy-intelligence"},{"title":"FarmRoad Agronomy Intelligence Daily Report Overview","sidebarTitle":"AI daily report overview","href":"/en/farmroad/daily-report-overview"}]},{"group":"Data Studio","pages":[{"title":"How do I create, edit, and delete dashboards in FarmRoad Data Studio?","sidebarTitle":"Create dashboard","href":"/en/farmroad/create-and-manage-dashboards"},{"title":"How do I create and manage graphs on a dashboard?","sidebarTitle":"Create graph","href":"/en/farmroad/data-studio-create-graph-on-dashboard"},{"title":"How do I create and manage heat maps on a dashboard?","sidebarTitle":"Create heat map","href":"/en/farmroad/data-studio-create-and-manage-heat-maps"},{"title":"How do I create and manage readings tables on a dashboard?","sidebarTitle":"Create readings table","href":"/en/farmroad/create-and-manage-readings-table"},{"title":"How do I export my data from FarmRoad?","sidebarTitle":"Export data","href":"/en/farmroad/data-studio-export-data"},{"title":"How do I manage time zones in Data Studio?","sidebarTitle":"Manage time zones","href":"/en/farmroad/data-studio-manage-time-zones"},{"title":"How can I view Growing Degree Days/Hours (GDD, GDH) in FarmRoad?","sidebarTitle":"Growing Degree Days/Hours (GDD/GDH)","href":"/en/farmroad/growing-degree-days-and-hours"},{"title":"What is the difference between the Growing Degree (GDD, GDH) calculation types?","sidebarTitle":"Calculation of GDD and GDH","href":"/en/farmroad/calcuation-of-GDD-and-GDH"}]},{"group":"Irrigation \u0026 Forecasting","pages":[{"title":"How can I use the FarmRoad solution for drip and drain irrigation monitoring?","sidebarTitle":"Drip and drain monitoring Overview","href":"/en/farmroad/drip-and-drain-monitoring"},{"title":"How can I use FarmRoad's Irrigation Forecast Dashboard to help me plan my irrigation schedule?","sidebarTitle":"Irrigation Forecast Dashboard overview","href":"/en/farmroad/irrigation-forecast-dashboard"},{"title":"What is FarmRoad's Inside Climate Prediction?","sidebarTitle":"Inside climate prediction overview","href":"/en/farmroad/inside-climate-prediction"}]},{"group":"Farm Management","pages":[{"title":"How do I add a farm?","sidebarTitle":"Add a farm","href":"/en/farmroad/add-farm"},{"title":"How do I add a compartment?","sidebarTitle":"Add a compartment","href":"/en/farmroad/add-compartment"},{"title":"How do I add a sector?","sidebarTitle":"Add a sector","href":"/en/farmroad/add-sector"},{"title":"How do I start a crop cycle?","sidebarTitle":"Start crop cycle","href":"/en/farmroad/start-crop-cycle"}]},{"group":"Organisation Management","pages":[{"group":"Preference Management","pages":[{"title":"How do I manage my profile?","sidebarTitle":"Manage profile","href":"/en/farmroad/organisation-management-manage-profile"},{"title":"How do I change measurement units?","sidebarTitle":"Change measurement units","href":"/en/farmroad/change-measurement-units"},{"title":"How do I change the language in FarmRoad?","sidebarTitle":"Change language","href":"/en/farmroad/change-languagae"}]},{"group":"Permission Management","pages":[{"title":"How do I create a team and give users farm access?","sidebarTitle":"Create a team","href":"/en/farmroad/create-a-team"},{"title":"How can I add new users to my FarmRoad account?","sidebarTitle":"Add new users","href":"/en/farmroad/add-users"},{"title":"How do roles and permissions work?","sidebarTitle":"Understanding roles and permissions","href":"/en/farmroad/roles-and-permissions"}]}]},{"group":"Alerts / Alerting","pages":[{"title":"How can I receive FarmRoad alerts via WhatsApp?","sidebarTitle":"Recieve alerts via WhatsApp","href":"/en/farmroad/recieve-alerts-whatsapp"},{"title":"How does the Sensor Offline alert work?","sidebarTitle":"Understanding Sensor Offline alerts","href":"/en/farmroad/Sensor-Offline-alert"},{"title":"How does the Gateway Offline alert work?","sidebarTitle":"Understanding Gateway Offline alerts","href":"/en/farmroad/understanding-gateway-offline-alerts"},{"title":"What happens to alerts when a gateway goes offline?","sidebarTitle":"Gateway offline alert behavior","href":"/en/farmroad/gateway-offline-alert-behavior"},{"title":"FarmRoad Alert FAQs","sidebarTitle":"Alert FAQs","description":null,"href":"/en/farmroad/alerts-faqs"}]},{"group":"Sensor \u0026 Gateway","pages":[{"title":"How do I set up my hardware?","sidebarTitle":"Set up hardware","href":"/en/farmroad/set-up-hardware"},{"title":"How do I connect my Gateway to WiFi? ","sidebarTitle":"Connect gateway to wifi","description":null,"href":"/en/farmroad/connect-gateway-to-wifi"},{"title":"How can I onboard a Folium/FarmRoad sensor device?","sidebarTitle":"Onboard a sensor","href":"/en/farmroad/onboard-a-sensor"},{"title":"How can I manage my fleet of FarmRoad Sensors and Gateways?","sidebarTitle":"Manage sensors and gateways","href":"/en/farmroad/manage-sensors-and-gateways"},{"title":"How to optimize your Folium-gateway signal range","sidebarTitle":"Folium-gateway signal range","href":"/en/farmroad/folium-sensor-gateway-signal-range"},{"title":"How do I install my Substrate Moisture Sensor?","sidebarTitle":"Install substrate moisture sensor","href":"/en/farmroad/install-substrate-moisture-sensor"},{"title":"How do I install my Plant Temperature Sensor","sidebarTitle":"Install plant temperature sensor","href":"/en/farmroad/install-plant-temperature-sensor"},{"title":"How to calibrate the Folium CO₂ sensor","sidebarTitle":"Calibrate Folium CO₂ sensor","href":"/en/farmroad/calibrate-folium-co2-sensor"},{"title":"Why is my Folium not connecting?","sidebarTitle":"Troubleshoot sensor and gateway","href":"/en/farmroad/troubleshoot-sensor-and-gateway"}]},{"group":"FarmRoad Mobile App","pages":[{"title":"How can I access FarmRoad on my mobile phone?","sidebarTitle":"Access FarmRoad on mobile","href":"/en/farmroad/download-farmroad-mobile-app"},{"group":"Crop Registration mobile","pages":[{"title":"How do I register for Crop Registration?","sidebarTitle":"Access Crop Registration","href":"/en/farmroad/access-crop-registration"},{"title":"How do I view, add, and edit crop registration records in FarmRoad Mobile?","sidebarTitle":"Add, view and edit crop registration records","href":"/en/farmroad/crop-registration-mobile-add-record"},{"title":"How do I export crop registration data from the FarmRoad mobile app?","sidebarTitle":"Export crop registration data","href":"/en/farmroad/crop-registration-mobile-export-data"},{"title":"Using Crop Registration offline","sidebarTitle":"Using Crop Registration offline","href":"/en/farmroad/using-crop-registration-offline"},{"title":"What are the roles and permissions for FarmRoad mobile crop registration?","sidebarTitle":"Roles and permissions for Crop Registration mobile","href":"/en/farmroad/roles-and-permissions-in-crop-registration-mobile"}]}]},{"group":"Crop Registration","pages":[{"title":"What measurement types are available in FarmRoad Crop Registration?","sidebarTitle":"Measurement types","mode":"wide","href":"/en/farmroad/crop-registration-measurement-types"},{"title":"FarmRoad Crop Registration measurement instructions","sidebarTitle":"Measurement instructions","href":"/en/farmroad/crop-registration-measurement-instructions"},{"group":"Crop Registration Web","pages":[{"title":"Where can I find Crop Registration in FarmRoad web?","sidebarTitle":"View Crop Registration","href":"/en/farmroad/where-to-find-crop-registration"},{"title":"How do I add a new crop registration record in FarmRoad web?","sidebarTitle":"Add crop registration record","href":"/en/farmroad/add-crop-registration-record"},{"title":"How do I edit a crop registration record in FarmRoad web?","sidebarTitle":"Edit crop registration record","href":"/en/farmroad/edit-crop-registration-record"},{"title":"How do I export crop registration data in FarmRoad web?","sidebarTitle":"Export crop registration data ","href":"/en/farmroad/export-crop-registration-data"},{"title":"What are the roles and permissions for FarmRoad Crop Registration web?","mode":"wide","sidebarTitle":"Roles and permissions for Crop Registration web","href":"/en/farmroad/crop-registration-roles-and-permissions"}]}]},{"group":"Crop Insights \u0026 Grower Guides","pages":[{"group":"Climate Analysis","pages":[{"title":"FarmRoad Climate Analysis","sidebarTitle":"Climate Analysis articles","hidden":true,"href":"/en/farmroad/climate-analysis-articles"},{"title":"Climate Analysis - tomatoes","href":"/en/farmroad/climate-analysis-tomatoes"},{"title":"Climate Analysis - blueberries","href":"/en/farmroad/climate-analysis-blueberries"},{"title":"Why has my Climate Analysis not generated?","sidebarTitle":"Climate Analysis requirements","href":"/en/farmroad/climate-analysis-requirements"}]},{"group":"Plant steering","pages":[{"title":"Plant Steering with FarmRoad Plant Balance ","sidebarTitle":"Understanding Plant Balance","href":"/en/farmroad/plant-balance"}]},{"group":"Yield","pages":[{"title":"FarmRoad Easy Yield Overview","sidebarTitle":" Easy Yield overview","href":"/en/farmroad/easy-yield-overview"},{"title":"Why has my yield prediction not generated?","sidebarTitle":"Missing yield prediction","href":"/en/farmroad/yield-prediction-not-generated"}]}]},{"group":"Activity Feed","pages":[{"title":"Adding a note in FarmRoad Activity Feed","sidebarTitle":"Add a note","href":"/en/farmroad/activity-feed-add-a-note"},{"title":"How do I record a crop yield?","sidebarTitle":"Record crop yield","href":"/en/farmroad/activity-feed-record-crop-yield"}]}]},{"group":"GrowPilot","pages":[{"title":"GrowPilot: Risk Alerts","href":"/en/growpilot/risk-alerts"},{"title":"GrowPilot: Evapotranspiration","href":"/en/growpilot/evapotranspiration"},{"title":"GrowPilot Localized weather forecasts","sidebarTitle":"GrowPilot Weather Forecasts","href":"/en/growpilot/weather-forecasts"}]}]},{"language":"fr","pages":[{"title":"fr","href":"/fr/farmroad/set-up-hardware"}]},{"language":"es","pages":[{"title":"es","href":"/es/farmroad/set-up-hardware"}]}]},"basePath":"","title":"How do I set up my hardware? - WayBeyond","deploymentId":"dpl_DyXGnKeCjZyA3sUdfMJ7FjkdBefg","buildId":"dpl_DyXGnKeCjZyA3sUdfMJ7FjkdBefg","dynamics":[],"chunks":[]}